Mail

From The DXSpider Documentation Wiki
Revision as of 18:35, 24 January 2023 by G0vgs (talk | contribs) (Created page with "==Mail== You can send and receive both personal mail and bulletins with DXSpider quite easily. ===The "directory" command=== To list mail you would use the DIRECTORY command. On its own, this command will output the last ten messages received by the node, either to or from yourself or bulletins such as "DX" and "ALL". As with other commands you can display more by specifying a number with the command. You should be aware that Spider will accept these commands by se...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Mail

You can send and receive both personal mail and bulletins with DXSpider quite easily.

The "directory" command

To list mail you would use the DIRECTORY command. On its own, this command will output the last ten messages received by the node, either to or from yourself or bulletins such as "DX" and "ALL". As with other commands you can display more by specifying a number with the command. You should be aware that Spider will accept these commands by separating with either a slash or a space, so dir new and dir/new work in the same way.

Example:

directory
directory/20
directory 20

Of course most of the time you will only want to list new mail sent to you personally since your last login. However you might also like to check for general mail received by the node. In fact if there is new mail for you, the cluster will tell you when you login. You will also be informed if new mail arrives for you during the time you are logged in. Mail is not only sent to callsigns though. Mail can also be sent to subjects like "all" or "local" or "dx" etc. You can treat these bulletins in the same way as personal mail with the directory command.

Examples:

directory/new
directory/own
directory/own/10
directory/all
directory/from <call>

The last option will only show mail from a callsign if it was sent to you personally or was sent as a bulletin. There are some additional commands and these can be found in the DXSpider Command Reference section.


Reading mail

The output of the DIRECTORY command could be something like this.

dir
20735      2      ALL   GW7SMV 21-Feb 1204Z REC 9E1S QSL TDY 50Mhz....
20823    308       UK    G0HDB 22-Feb 2334Z Help - which district code?
20824    105      ALL     W9AE 23-Feb 0349Z S0NY QSL address?
20825      2       UK    G0LRJ 23-Feb 0806Z QSL REC LZ2CJ/1.CARD NO-750.
20858      2      ALL   GW7SMV 24-Feb 0905Z REC S92DX QSL CARD TDY 50Mhz
20921    200      ALL   GM4FDM 27-Feb 2203Z Trip to VP8
20949    375      ALL     K0MN 27-Feb 0428Z ST0P cards are gd @ ARRL
20950      2       UK    G0LRJ 28-Feb 0835Z QSL REC SV9/IZ0CKJ/P EU-187.
20987    569      ALL   GD0TEP  1-Mar 1733Z Portable contests
21076      2      ALL    G4AFJ  3-Mar 1743Z kh6nd/kh5 qsl received
21184-p  599   GW4HAT    G0VGS  4-Mar 1518Z Re: Time

The first column is the actual message number. If the message is a personal one to you, you will see a letter 'p' after this number. If the message has been read, there will be a '-' between the message number and the 'p'. This only works for personal messages. The next column shows the file size of the message. The third column shows the address the message was sent to and the next column shows who sent it. The rest is fairly self-explanatory.

Reading a message is as simple as typing read, followed by the message number that you wish to read.

Example:

read 25

will read message number 25. However the mail will be displayed in it's entirety unless you specify a page length. You can set your page length to any number you like and when the message reaches that number of lines you will get a prompt giving you options.

Example:

set/page 20

Sending mail

Sending mail is done in the time honoured way. First you specify a recipient for the message, then you will be prompted for a subject. Once you have done this you will be asked to type your message. Please remember that there is no automatic word wrap, so unless you are using a client that wraps lines automatically, remember to hit return at the end of each line.

Example:

send m0azm
Enter Subject (30 characters):
See you Thursday
Enter Message /EX to send or /ABORT to exit
Hi Ian,
Just a quick note to say that I can make Thursday after all.  The
appointment I had has cancelled so we are go!
Cheers
Ian

At this point you can either hit return and enter /ex to send the message or use /abort at any time to abort it. You can now display the message in the normal way. There are several send options and these are listed in the Command Set section. These include sending mail to several recipients and asking for a return receipt.

Replying to mail

If mail is addressed to you or to a bulletin address, you can use the REPLY command to reply to it. Using this command, the subject will be automatically set for you as "Re: subject", whatever the subject was.

Example:

reply 2500

Deleting mail

 To delete a message, you use the delete command.  You can only delete
 messages sent to or received by yourself.  Bulletins are dealt with
 automatically or by the sysop.